blogs+list_page_heading

topexwiper


Improper use of automobile wiper blades may lead to scrapping ahead of schedule, or the rain will not be clean, which will affect the driver’s driving. Therefore, the wiper manufacturers have five points to note when repairing the wiper wiper.
 
First, the premature scrapping of some wiper blades is directly related to improper car washing. If the car does not pay attention to wipe the front windshield, the surface of the oil film is washed off, one is not conducive to the influx of rain, resulting in easy to stop the rain on the glass surface, the second is to increase the friction between the rubber sheet and the glass surface. This is also the cause of the momentary pause phenomenon of the wiper blade due to scratches. If the wiper blade does not move and the motor continues to operate, it can easily cause the motor to burn out.
 
Second, if there are strong things on the windshield, such as pigeons and other dry excrement of birds, must not be directly wiped hard with a wiper, please first clear the bird droppings by hand. These hard objects can easily cause partial damage to the wiper blades, causing rain and scratches to be unclean.

Third, it is not advisable to use a wiper blade to remove dust from the surface of the windshield. Even if you want to do this, be sure to spray glass water at the same time, and never dry it.
Fourth, even if there is rain, if the rainfall is not enough to start the wiper blade, it should not be scraped. Be sure to wait until there is enough rain on the glass surface. Saying “enough” here doesn’t stop the driver’s eyes.
 
5. It must be used in the presence of rain. The wiper blade cleans the rain on the front windshield. You can’t use it without rain, never dry it. The increase of frictional resistance due to no water causes damage to the rubber blade and the wiper motor.
 
In addition, improper use of wiper blades, including wipers, wiper blades, and wipers, will cause wiper blades to be replaced in advance or not clean. The result of a wiper blade scraping is generally a few seconds after the scraping stops. Wait a moment, the glass surface of the water is blown to achieve the best removal effect. The wiper blade I used was a flat wiper blade and a hybrid wiper blade. I still feel pretty good.

topexwiper
Phenomenon 1 : When the wiper moves in a certain direction , it jumps on the glass , causing an abnormal sound . The Reason for formation : This condition is generally due to the presence of sand grains in the grooves on both sides of the wiper skin , so that it cannot maintain the correct angle with the glass through normal deformation . Therefore , please adjust the wiper angle first . The Solution : When the wiper is dry , move the wiper to the maintenance position , lift the wiper in question , twist the wiper blades several times for the left and right , and generally squeeze the sand particles out of the groove . If this does not work , or if the wipers are wet , use a small slotted screwdriver to scratch the head along the grooves on both sides with the wiper blade . Or because the wiper has a relatively loose rubber clip , use a needle-nose pliers to clamp the gap between the joints and the rubber clip . Phenomenon 2 : After the wipers are brushed , there is an oily water film on the glass and the sound is loud . Cause : There is oil on the front windshield , and the wiper can't stick to the glass , causing a loud sound . Solution : Spray the front glass surface with household glass (washing spirit , washing liquid with detergent ) , then start the wiper , and pour some clean water on the front file to help clean it . Phenomenon 3 : After the wiper is brushed , the front window leaves a curved watermark affecting the line of sight . Cause : Dirt on the surface of the wiper skin and the glass , causing the wiper skins to not adhering to the glass . Solution : If the wiper is dry , spray some glass water or pour some water to make it moist , move the wiper to the maintenance position , lift the wiper in question , wipe the wiper in contact with the glass of a clean paper towel . Face , wipe dirt , you can solve . If there is still a slight watermark , use No . 0 sandpaper (fine sandpaper ) , dip in water , and lightly polish it from top to bottom several times (be careful not to force evenly ) . This will completely solve the problem . The In the end , we need to know that the wiper blade itself is a consumable product , whether it is a bone wiper blade or a boneless wiper blade, as well as a flat wiper blade and hybrid wiper blade are all rubber products , usually for one year or 20,000 kilometers will need to be replaced . Rainy days and frequent use will be replaced in time depending on the situation .



topexwiper
Phenomenon 1 : When the wiper moves in a certain direction , it jumps on the glass , causing an abnormal sound . The Reason for formation : This condition is generally due to the presence of sand grains in the grooves on both sides of the wiper skin , so that it cannot maintain the correct angle with the glass through normal deformation . Therefore , please adjust the wiper angle first . The Solution : When the wiper is dry , move the wiper to the maintenance position , lift the wiper in question , twist the wiper blades several times for the left and right , and generally squeeze the sand particles out of the groove . If this does not work , or if the wipers are wet , use a small slotted screwdriver to scratch the head along the grooves on both sides with the wiper blade . Or because the wiper has a relatively loose rubber clip , use a needle-nose pliers to clamp the gap between the joints and the rubber clip . Phenomenon 2 : After the wipers are brushed , there is an oily water film on the glass and the sound is loud . Cause : There is oil on the front windshield , and the wiper can't stick to the glass , causing a loud sound . Solution : Spray the front glass surface with household glass (washing spirit , washing liquid with detergent ) , then start the wiper , and pour some clean water on the front file to help clean it . Phenomenon 3 : After the wiper is brushed , the front window leaves a curved watermark affecting the line of sight . Cause : Dirt on the surface of the wiper skin and the glass , causing the wiper skins to not adhering to the glass . Solution : If the wiper is dry , spray some glass water or pour some water to make it moist , move the wiper to the maintenance position , lift the wiper in question , wipe the wiper in contact with the glass of a clean paper towel . Face , wipe dirt , you can solve . If there is still a slight watermark , use No . 0 sandpaper (fine sandpaper ) , dip in water , and lightly polish it from top to bottom several times (be careful not to force evenly ) . This will completely solve the problem . The In the end , we need to know that the wiper blade itself is a consumable product , whether it is a bone wiper blade or a boneless wiper blade, as well as a flat wiper blade and hybrid wiper blade are all rubber products , usually for one year or 20,000 kilometers will need to be replaced . Rainy days and frequent use will be replaced in time depending on the situation .



topexwiper

The new car wiper has not heard that the scrapping is not clean , but we often run into a new wiper that we just replaced and run for a while . Although the problem is not great , it is still very annoying . It is inconvenient if it is rainy days . The same is true of my car , and the problem of scratching does not always appear . After the last time a friend that worked in the topexwiper for many years analyzed the reason , not only didn't change the 
 bar , it was as clean as the new car . 
The reason why the scrapping is not clean : A friend of topexwiper told me that there is mainly invisible dirt on the glass . First , the car stopped at the downwind of the central air-conditioning cool tower . The cold water tower shattered the particles of water and dropped it on the glass to form a small white spot . After drying , it was difficult to completely remove it .
Second , the car was parked under a tree and the insects secret it . The mucus sticks to the glass of the car ; the third is the mucus of insects that crash at long distances . Because these things stick to the glass , they are hardly completely removed (but not visible ) from water and a cloth , and a rugged surface is formed into the glass . In this way , when the wiper is used , the glass is not cleanly scraped . Seeing the above reasons , many of my friends never thought about it just like me ! At the time , I was also surprised that the friend that had worked at the topexwiper had given me a measure to share with everyone : soak the glass of water and gently touch the glass by hand . If the glass surface is not smooth , there is a foreign object .
When you clear it , you can try to wipe it with warm water several times and then gently rub it with your hands . You can also use the newspaper to remove these hard-to-remove dirts little by little . The effect is good . After the water is washed , touch the glass of your hands . Very smooth . At this point , open the wiper to try . It's very clean . Owners with such conditions can try . Includes a flat wiper blade

Topexwiper's working friends share that : The above experience may not be suitable for other situations in which the front gear is not clean . If there is no feeling of unevenness after touching the glass , you may need to change the wiper strip .

topexwiper Apr 19 · blogs+tags flat wiper blade