blogs+list_page_heading

topexwiper


Improper use of automobile wiper blades may lead to scrapping ahead of schedule, or the rain will not be clean, which will affect the driver’s driving. Therefore, the wiper manufacturers have five points to note when repairing the wiper wiper.
 
First, the premature scrapping of some wiper blades is directly related to improper car washing. If the car does not pay attention to wipe the front windshield, the surface of the oil film is washed off, one is not conducive to the influx of rain, resulting in easy to stop the rain on the glass surface, the second is to increase the friction between the rubber sheet and the glass surface. This is also the cause of the momentary pause phenomenon of the wiper blade due to scratches. If the wiper blade does not move and the motor continues to operate, it can easily cause the motor to burn out.
 
Second, if there are strong things on the windshield, such as pigeons and other dry excrement of birds, must not be directly wiped hard with a wiper, please first clear the bird droppings by hand. These hard objects can easily cause partial damage to the wiper blades, causing rain and scratches to be unclean.

Third, it is not advisable to use a wiper blade to remove dust from the surface of the windshield. Even if you want to do this, be sure to spray glass water at the same time, and never dry it.
Fourth, even if there is rain, if the rainfall is not enough to start the wiper blade, it should not be scraped. Be sure to wait until there is enough rain on the glass surface. Saying “enough” here doesn’t stop the driver’s eyes.
 
5. It must be used in the presence of rain. The wiper blade cleans the rain on the front windshield. You can’t use it without rain, never dry it. The increase of frictional resistance due to no water causes damage to the rubber blade and the wiper motor.
 
In addition, improper use of wiper blades, including wipers, wiper blades, and wipers, will cause wiper blades to be replaced in advance or not clean. The result of a wiper blade scraping is generally a few seconds after the scraping stops. Wait a moment, the glass surface of the water is blown to achieve the best removal effect. The wiper blade I used was a flat wiper blade and a hybrid wiper blade. I still feel pretty good.

topexwiper
Phenomenon 1 : When the wiper moves in a certain direction , it jumps on the glass , causing an abnormal sound . The Reason for formation : This condition is generally due to the presence of sand grains in the grooves on both sides of the wiper skin , so that it cannot maintain the correct angle with the glass through normal deformation . Therefore , please adjust the wiper angle first . The Solution : When the wiper is dry , move the wiper to the maintenance position , lift the wiper in question , twist the wiper blades several times for the left and right , and generally squeeze the sand particles out of the groove . If this does not work , or if the wipers are wet , use a small slotted screwdriver to scratch the head along the grooves on both sides with the wiper blade . Or because the wiper has a relatively loose rubber clip , use a needle-nose pliers to clamp the gap between the joints and the rubber clip . Phenomenon 2 : After the wipers are brushed , there is an oily water film on the glass and the sound is loud . Cause : There is oil on the front windshield , and the wiper can't stick to the glass , causing a loud sound . Solution : Spray the front glass surface with household glass (washing spirit , washing liquid with detergent ) , then start the wiper , and pour some clean water on the front file to help clean it . Phenomenon 3 : After the wiper is brushed , the front window leaves a curved watermark affecting the line of sight . Cause : Dirt on the surface of the wiper skin and the glass , causing the wiper skins to not adhering to the glass . Solution : If the wiper is dry , spray some glass water or pour some water to make it moist , move the wiper to the maintenance position , lift the wiper in question , wipe the wiper in contact with the glass of a clean paper towel . Face , wipe dirt , you can solve . If there is still a slight watermark , use No . 0 sandpaper (fine sandpaper ) , dip in water , and lightly polish it from top to bottom several times (be careful not to force evenly ) . This will completely solve the problem . The In the end , we need to know that the wiper blade itself is a consumable product , whether it is a bone wiper blade or a boneless wiper blade, as well as a flat wiper blade and hybrid wiper blade are all rubber products , usually for one year or 20,000 kilometers will need to be replaced . Rainy days and frequent use will be replaced in time depending on the situation .



topexwiper
Phenomenon 1 : When the wiper moves in a certain direction , it jumps on the glass , causing an abnormal sound . The Reason for formation : This condition is generally due to the presence of sand grains in the grooves on both sides of the wiper skin , so that it cannot maintain the correct angle with the glass through normal deformation . Therefore , please adjust the wiper angle first . The Solution : When the wiper is dry , move the wiper to the maintenance position , lift the wiper in question , twist the wiper blades several times for the left and right , and generally squeeze the sand particles out of the groove . If this does not work , or if the wipers are wet , use a small slotted screwdriver to scratch the head along the grooves on both sides with the wiper blade . Or because the wiper has a relatively loose rubber clip , use a needle-nose pliers to clamp the gap between the joints and the rubber clip . Phenomenon 2 : After the wipers are brushed , there is an oily water film on the glass and the sound is loud . Cause : There is oil on the front windshield , and the wiper can't stick to the glass , causing a loud sound . Solution : Spray the front glass surface with household glass (washing spirit , washing liquid with detergent ) , then start the wiper , and pour some clean water on the front file to help clean it . Phenomenon 3 : After the wiper is brushed , the front window leaves a curved watermark affecting the line of sight . Cause : Dirt on the surface of the wiper skin and the glass , causing the wiper skins to not adhering to the glass . Solution : If the wiper is dry , spray some glass water or pour some water to make it moist , move the wiper to the maintenance position , lift the wiper in question , wipe the wiper in contact with the glass of a clean paper towel . Face , wipe dirt , you can solve . If there is still a slight watermark , use No . 0 sandpaper (fine sandpaper ) , dip in water , and lightly polish it from top to bottom several times (be careful not to force evenly ) . This will completely solve the problem . The In the end , we need to know that the wiper blade itself is a consumable product , whether it is a bone wiper blade or a boneless wiper blade, as well as a flat wiper blade and hybrid wiper blade are all rubber products , usually for one year or 20,000 kilometers will need to be replaced . Rainy days and frequent use will be replaced in time depending on the situation .



topexwiper

1. Before buying a wiper blade, you must first confirm the specifications of the wiper blade on your car.
For the specification of your own car's wiper, you can look through the vehicle's instruction manual, look at the model of the wiper blade marked above, or call a consultant for service consulting, and confirm the connection of the wiper blade and the wiper arm. The wiper blade I use is the flat wiper blade. Its model number is
Product name 5 in 1 multifunction flat wiper blade model No. T-990
Adaptor material POM
Spoiler material: TPR
Refill material natural rubber
Joint material metal
Size 12′′-28′′
Hand driving LHD/RHD
Overseas Market South-east Asia, Europe, North and South America, India, Oceania etc.
Features 1) Graphite coated natural rubber.

  1. Aerodynamic design.
  2. Even pressure.
  3. Fit for all season, all weather.
  4. smooth, chatter-free
Trade Terms 1) The price is based on FOB Xiamen or Guangzhou
  1. Supply ability: 170,000 pieces per day
  2. MOQ: 2000PCS
  3. Payment: T/T, L/C 30% deposit before production, balance 70% upon receive the BL copy
, And hybrid wiper blade, are good, of course, scraping clean is the last word.
2. When choosing a wiper blade, first look at the packaging.
The packaging of genuine products is clearly written on the box, accurate overprinting, and vivid colors, and trademarks containing complete product information are affixed to the packaging and products.
3. After observing the wiper blade, observe its structure.
The normal wiper motor is designed according to a single strip (unless the original wiper motor design is a two-piece design). Wiper blades of two or more strips will increase the motor load and affect the wiping effect. Apply a certain pulling force to the strip from the middle of the wiper blade by hand, and the strip will not fall off from the corner. Whether it is a bone wiper blade or a boneless wiper blade, each joint must be flexible and free to rebound after being pressed by hand from the middle of the strip.
4. After installing the wiper blade, check the wiper status.
There should be no phenomenon that wiper blades swing unsteadily, abnormally beats, and the strips and glass cannot be completely attached to each other, resulting in scratches and the like. After scraping, no fine streaks, mists, and lines remain on the surface of the glass. Also pay attention to whether or not the motor has abnormal noise, and a good wiper blade can reduce the motor load.

topexwiper Apr 19 · blogs+tags hybrid wiper blade